Distillation Cooling Water System

完璧な温度制御ソリューションについては、今すぐお問い合わせください。

Introduction to distillation cooling water system

The distillation cooling water system refers to a machine that prepares pure water through distillation. Distilled water can be divided into once and multiple times. After the water is distilled once, the non-volatile components in the container are removed, and the volatile components enter the initial fraction of distilled water. Usually only the middle part of the fraction is collected, accounting for about 60%. In order to obtain purer water, add alkaline potassium permanganate solution to primary distilled water to remove organic matter and carbon dioxide; add non-volatile acid to turn ammonia into non-volatile ammonium salts. Since glass contains a small amount of water-soluble components, quartz stills can be used to obtain very pure water during secondary or multiple distillations. The pure water obtained should be stored in quartz or silver containers.

Characteristics of distillation cooling water system

Evaporator: Use tube falling film evaporation technology to ensure that the feed water is evenly distributed on the inner wall of each evaporation tube to form water film evaporation. The upper-effect pure steam provides heat energy to the lower-effect evaporator and completes its evaporation and liquefaction to form distilled water.

Vapor-liquid separator: adopts split-type four-separation technology for soda and water (centrifugal separation of soda and water, down-rotating blade separator, wire mesh to capture water droplets, and upper-rotating blade separator) to ensure that the distilled water has low water heat source and endotoxin content. . The requirements for pure water are relatively low, and distilled water that meets pharmacopoeia standards can be produced below single-stage reverse osmosis (10us/cm).

Preheater: U-shaped tube heat exchanger, heat exchanger, good mechanical performance and long service life.

Condenser: Unique double condenser design, special multi-pass structure, sufficient heat exchange, no need for cooling water to reach the required temperature of distilled water.

Pipeline: The pipeline design has no water storage, no dead ends, and low equipment failure rate. Pipe connections adopt new sanitary clamp connections. The inside and outside are mirror polished, arranged neatly and beautifully, and the operation is quick and convenient.

Configuration: regulating valve, automatic compensation valve, throttle valve, conductivity meter, and thermometer are all high-tech products at home and abroad, with beautiful appearance and complete functions.

Water source: The water source required by the equipment must be pure water produced by reverse osmosis water.

Insulation: Both the evaporator and preheater are made from chlorine- and asbestos-free mineral wool insulation and covered with stainless steel cladding.

Economical and energy-saving: Because the multi-effect distilled water machine uses secondary steam step by step for each effect, the industrial steam utilization rate is high and the energy-saving effect is obvious. As the efficiency of the evaporator increases, this energy saving effect becomes more obvious. At the same time, the amount of cooling water also decreases greatly as the number of effects increases.

Control system: Adopts PLC automatic control technology to meet customers’ different control requirements. From the basic judgment and distribution of distilled water quality, to the continuous adjustment of each medium, linkage with the storage system, hierarchical password control and even the control of evaporation changes and other more advanced ones, it can be said that it is meticulous.

Paperless records: Use paperless records to record actual production conditions.

Factory performance test of the complete machine: In the complete machine test workshop, the actual working environment is simulated and the complete machine is tested according to the determined procedures.

Eメール info@lneya.com    WeChat ID： +8615251628237    WhatsApp： +86 17851209193

精密冷凍機/小型冷凍機

(カスタムデザイン)

チラーは様々な産業や研究所で広く使用することができ、カスタマイズされた設計をサポートしています。

循環式チラー

(カスタムデザイン)

私達の再循環のスリラーは低温冷凍の技術を採用し、温度は- 120℃と低く、さまざまな付属品はカスタマイズ可能です。

低温チラー

(カスタムデザイン)

当社は、-150℃の温度制御範囲を持つ低温冷凍機の生産を専門としており、さまざまな業界の冷凍ニーズを満たすことができます。

Chillers for Automotive Test

(カスタムデザイン)

車両品質テスト用温度シミュレーション：バッテリー寿命テスト、燃料噴射装置/モーターテストベンチ、エアバッグテスト、コンポーネントテストベンチなど。

Chillers for Semiconductor

(カスタムデザイン)

電子部品の精密な温度制御に適しています。過酷な環境に対応する半導体電子部品の製造では、ICパッケージの組み立てやエンジニアリング、製造テストの段階で、電子温度テストやその他の環境テストシミュレーションが行われます。

バッテリーエネルギー貯蔵システム用液体冷却

(カスタムデザイン)

ZLFQシリーズ

(カスタムデザイン)

クーラント分配ユニット

液冷装置は、半導体試験、電子機器恒温試験、サーバー支持インフラ冷却、その他の流体温度制御場所に適しています。

MDサーマルチャックシリーズ

(カスタムデザイン)

RFデバイスや高密度パワーデバイス（IGBTやMOSFET）のテストに使用され、実験用フラットパネル（プラズマ、生物学的製品、バッテリー）などの急速冷却にも使用できる。

スクリュー冷凍機 (カスタムデザイン)

低温スクリュー冷凍機と常温スクリュー冷凍機