Distillation Cooling Water System

완벽한 온도 제어 솔루션을 위해 지금 바로 문의하세요.

Introduction to distillation cooling water system

The distillation cooling water system refers to a machine that prepares pure water through distillation. Distilled water can be divided into once and multiple times. After the water is distilled once, the non-volatile components in the container are removed, and the volatile components enter the initial fraction of distilled water. Usually only the middle part of the fraction is collected, accounting for about 60%. In order to obtain purer water, add alkaline potassium permanganate solution to primary distilled water to remove organic matter and carbon dioxide; add non-volatile acid to turn ammonia into non-volatile ammonium salts. Since glass contains a small amount of water-soluble components, quartz stills can be used to obtain very pure water during secondary or multiple distillations. The pure water obtained should be stored in quartz or silver containers.

Characteristics of distillation cooling water system

Evaporator: Use tube falling film evaporation technology to ensure that the feed water is evenly distributed on the inner wall of each evaporation tube to form water film evaporation. The upper-effect pure steam provides heat energy to the lower-effect evaporator and completes its evaporation and liquefaction to form distilled water.

Vapor-liquid separator: adopts split-type four-separation technology for soda and water (centrifugal separation of soda and water, down-rotating blade separator, wire mesh to capture water droplets, and upper-rotating blade separator) to ensure that the distilled water has low water heat source and endotoxin content. . The requirements for pure water are relatively low, and distilled water that meets pharmacopoeia standards can be produced below single-stage reverse osmosis (10us/cm).

Preheater: U-shaped tube heat exchanger, heat exchanger, good mechanical performance and long service life.

Condenser: Unique double condenser design, special multi-pass structure, sufficient heat exchange, no need for cooling water to reach the required temperature of distilled water.

Pipeline: The pipeline design has no water storage, no dead ends, and low equipment failure rate. Pipe connections adopt new sanitary clamp connections. The inside and outside are mirror polished, arranged neatly and beautifully, and the operation is quick and convenient.

Configuration: regulating valve, automatic compensation valve, throttle valve, conductivity meter, and thermometer are all high-tech products at home and abroad, with beautiful appearance and complete functions.

Water source: The water source required by the equipment must be pure water produced by reverse osmosis water.

Insulation: Both the evaporator and preheater are made from chlorine- and asbestos-free mineral wool insulation and covered with stainless steel cladding.

Economical and energy-saving: Because the multi-effect distilled water machine uses secondary steam step by step for each effect, the industrial steam utilization rate is high and the energy-saving effect is obvious. As the efficiency of the evaporator increases, this energy saving effect becomes more obvious. At the same time, the amount of cooling water also decreases greatly as the number of effects increases.

Control system: Adopts PLC automatic control technology to meet customers’ different control requirements. From the basic judgment and distribution of distilled water quality, to the continuous adjustment of each medium, linkage with the storage system, hierarchical password control and even the control of evaporation changes and other more advanced ones, it can be said that it is meticulous.

Paperless records: Use paperless records to record actual production conditions.

Factory performance test of the complete machine: In the complete machine test workshop, the actual working environment is simulated and the complete machine is tested according to the determined procedures.

이메일: info@lneya.com    WeChat ID: +8615251628237    WhatsApp: +86 17851209193

정밀 냉각기 / 소형 냉각기

(맞춤형 디자인)

이 냉각기는 다양한 산업 및 실험실에서 널리 사용될 수 있으며 맞춤형 설계를 지원합니다.

재순환 냉각기

(맞춤형 디자인)

당사의 재순환 냉각기는 저온 냉동 기술을 채택하고 온도가 -120℃까지 낮으며 다양한 액세서리를 사용자 정의 할 수 있습니다.

저온 냉각기

(맞춤형 디자인)

당사는 -150°C의 낮은 온도 제어 범위를 갖춘 저온 냉각기 생산을 전문으로 하며, 다양한 산업의 냉장 요구 사항을 충족할 수 있습니다.

자동차 테스트용 냉각기

(맞춤형 디자인)

차량 품질 테스트를 위한 온도 시뮬레이션: 배터리 수명 테스트, 연료 인젝터/모터 테스트 벤치, 에어백 테스트, 부품 테스트 벤치 등

반도체용 냉각기

(맞춤형 디자인)

전자 부품의 정밀한 온도 제어에 적합합니다. 열악한 환경을 위한 반도체 전자 부품 제조에서 IC 패키징 조립 및 엔지니어링 및 생산 테스트 단계에는 전자 열 테스트 및 기타 환경 테스트 시뮬레이션이 포함됩니다.

배터리 에너지 저장 시스템용 액체 냉각

(맞춤형 디자인)

ZLFQ 시리즈

(맞춤형 디자인)

냉각수 분배 장치

액체 냉각 장비는 반도체 테스트, 전자 장비 항온 테스트, 서버 지원 인프라 냉각 및 기타 유체 온도 제어 장소에 적합합니다.

MD 써멀 척 시리즈

(맞춤형 디자인)

RF 디바이스 및 고밀도 전력 디바이스(IGBT 및 MOSFET) 테스트에 사용되며 실험실 평판(플라즈마, 생물학적 제품, 배터리) 등의 급속 냉각에도 사용할 수 있습니다.

스크류 칠러 (맞춤형 디자인)

저온 스크류 냉각기 및 실온 스크류 냉각기