Distillation Cooling Water System

Contacte-nos hoje para obter a solução perfeita de controlo da temperatura

Introduction to distillation cooling water system

The distillation cooling water system refers to a machine that prepares pure water through distillation. Distilled water can be divided into once and multiple times. After the water is distilled once, the non-volatile components in the container are removed, and the volatile components enter the initial fraction of distilled water. Usually only the middle part of the fraction is collected, accounting for about 60%. In order to obtain purer water, add alkaline potassium permanganate solution to primary distilled water to remove organic matter and carbon dioxide; add non-volatile acid to turn ammonia into non-volatile ammonium salts. Since glass contains a small amount of water-soluble components, quartz stills can be used to obtain very pure water during secondary or multiple distillations. The pure water obtained should be stored in quartz or silver containers.

Characteristics of distillation cooling water system

Evaporator: Use tube falling film evaporation technology to ensure that the feed water is evenly distributed on the inner wall of each evaporation tube to form water film evaporation. The upper-effect pure steam provides heat energy to the lower-effect evaporator and completes its evaporation and liquefaction to form distilled water.

Vapor-liquid separator: adopts split-type four-separation technology for soda and water (centrifugal separation of soda and water, down-rotating blade separator, wire mesh to capture water droplets, and upper-rotating blade separator) to ensure that the distilled water has low water heat source and endotoxin content. . The requirements for pure water are relatively low, and distilled water that meets pharmacopoeia standards can be produced below single-stage reverse osmosis (10us/cm).

Preheater: U-shaped tube heat exchanger, heat exchanger, good mechanical performance and long service life.

Condenser: Unique double condenser design, special multi-pass structure, sufficient heat exchange, no need for cooling water to reach the required temperature of distilled water.

Pipeline: The pipeline design has no water storage, no dead ends, and low equipment failure rate. Pipe connections adopt new sanitary clamp connections. The inside and outside are mirror polished, arranged neatly and beautifully, and the operation is quick and convenient.

Configuration: regulating valve, automatic compensation valve, throttle valve, conductivity meter, and thermometer are all high-tech products at home and abroad, with beautiful appearance and complete functions.

Water source: The water source required by the equipment must be pure water produced by reverse osmosis water.

Insulation: Both the evaporator and preheater are made from chlorine- and asbestos-free mineral wool insulation and covered with stainless steel cladding.

Economical and energy-saving: Because the multi-effect distilled water machine uses secondary steam step by step for each effect, the industrial steam utilization rate is high and the energy-saving effect is obvious. As the efficiency of the evaporator increases, this energy saving effect becomes more obvious. At the same time, the amount of cooling water also decreases greatly as the number of effects increases.

Control system: Adopts PLC automatic control technology to meet customers’ different control requirements. From the basic judgment and distribution of distilled water quality, to the continuous adjustment of each medium, linkage with the storage system, hierarchical password control and even the control of evaporation changes and other more advanced ones, it can be said that it is meticulous.

Paperless records: Use paperless records to record actual production conditions.

Factory performance test of the complete machine: In the complete machine test workshop, the actual working environment is simulated and the complete machine is tested according to the determined procedures.

Correio eletrónico: info@lneya.com    ID WeChat: +8615251628237    WhatsApp: +86 17851209193

Chillers de precisão / Chillers pequenos

(Desenhos personalizados)

O refrigerador pode ser amplamente utilizado em várias indústrias e laboratórios, e suporta um design personalizado.

Chillers de recirculação

(Desenhos personalizados)

Nosso resfriador de recirculação adota tecnologia de refrigeração de baixa temperatura, a temperatura é tão baixa quanto -120 ℃ e vários acessórios são personalizáveis.

Refrigeradores de baixa temperatura

(Desenhos personalizados)

Somos especializados na produção de refrigeradores de baixa temperatura com uma gama de controlo de temperatura tão baixa como -150°C, que pode satisfazer as necessidades de refrigeração de diferentes indústrias.

Chillers for Automotive Test

(Desenhos personalizados)

Simulação da temperatura para o ensaio da qualidade do veículo: ensaio da duração da bateria, banco de ensaio do injetor/motor de combustível, ensaio do airbag, banco de ensaio de componentes, etc.

Chillers for Semiconductor

(Desenhos personalizados)

Adequado para o controlo preciso da temperatura de componentes electrónicos. No fabrico de componentes electrónicos de semicondutores para ambientes agressivos, as fases de montagem de embalagens IC e de ensaios de engenharia e produção incluem ensaios térmicos electrónicos e outras simulações de ensaios ambientais.

Resfriamento líquido para sistemas de armazenamento de energia de baterias

(Desenhos personalizados)

Série ZLFQ

(Desenhos personalizados)

Unidade de distribuição do líquido de refrigeração

O equipamento de arrefecimento líquido é adequado para testes de semicondutores, testes de temperatura constante de equipamento eletrónico, infra-estruturas de apoio a servidores de arrefecimento e outros locais de controlo de temperatura de fluidos.

Série de mandris térmicos MD

(Desenhos personalizados)

É utilizado para testar dispositivos RF e dispositivos de potência de alta densidade (IGBTs e MOSFETs), podendo também ser utilizado para o arrefecimento rápido de painéis planos de laboratório (plasma, produtos biológicos, baterias), etc.

Resfriadores de parafuso (Desenhos personalizados)

Refrigeradores de parafuso a baixa temperatura e refrigeradores de parafuso a temperatura ambiente