Combinação de aquecedor e refrigerador

2023/03/28 ClassificaçãoNotícias do sector 210

Combinação de aquecedor e refrigerador

Installation and commissioning of heater chiller combo:

The heater chiller combo consists of two systems, two computer PC boards, each controls the corresponding system, and automatically adjusts heating or cooling according to process requirements through heat transfer oil circulation. It consists of pumps, heating tubes, cooling heat exchangers, refrigeration systems, temperature control systems, piping and racks. The heat transfer oil flows between the heat medium pipeline of the unit and the jacket or coil of the reactor, the circulation pump, the heat transfer oil pipeline, the heating device and the cooling device constitute the basic circuit of the heat medium.

First connect the power supply of the heater chiller combo. Before installation, it is necessary to understand the circuit requirements of the all-in-one machine. If conditions permit, try to connect it in parallel with other equipment on the circuit, and it is recommended to set the switch of the high and low temperature all-in-one machine separately. Because this can ensure that the circuit of other equipment or the equipment itself fails without affecting normal use. After the installation is complete, plug in the power plug, and turn on the switch of the main power supply and the drain valve. The switch of the main power supply is self-evident. Basically no one will ignore this switch, but the switch of the drain valve will be ignored by many people without paying attention. The consequence of not opening the drain valve switch is that the heater chiller combo cannot perform water circulation during operation, and a large amount of water will accumulate inside the all-in-one machine, hindering its normal operation, and even causing electric leakage. After ensuring that the switches of the main power supply and the drain valve are both on, adjust the data required for the test. At this time, it should be noted that the input data cannot exceed the standard limited by the machine itself. After the data is debugged, prepare for observation and record when necessary. After the natural shutdown according to the specified time, the power should be turned off in time. Prevent electric leakage and accidents when left unattended.

Soluções personalizadas para o seu negócio

Sistemas de arrefecimento e aquecimento (série SUNDI)

Gama de controlo de temperatura: -120°C a +350°C

Application: Various Reactors (Microchannels, Glass, Jacketed Reactors, etc.), Distillation or Extraction System, Laboratory, University, Research Institute, Aerospace, Automotive Industry, Semiconductor and Electrical Test, Chemical, Pharmaceutical, Petrochemical, Biochemical, Medical, Hospital, R&D Workshop, Aerospace, Biological and Other Industries.

Faixa de temperatura

Série -40 ~ +200°C

Série -10 ~ +200°C

Série -25 ~ +200°C

Série -25 ~ +300°C

Série -45 ~ +250°C

Série -45 ~ +300°C

Série -60 ~ +250°C

Série -60 ~ +300°C

Série -70 ~ +250°C

Série -80 ~ +250°C

Série -90 ~ +250°C

Série -100 ~ +100°C

-25 ~ +200°C uma máquina para dois reactores

-40 ~ +200°C uma máquina para dois reactores

Capacidade de arrefecimento

até 3kW

até 15kW

até 200kW

até 25kW

até 60kW

até 25kW

até 15kW

até 80kW

até 10*2kW

Sistemas de arrefecimento e aquecimento (série WTD)

（Reactores de canal micro / tubo especializados）

Gama de controlo de temperatura: -70°C a +300°C

Design especializado para micro canal (pequena capacidade de retenção de líquido, forte capacidade de troca de calor, sistema de circulação de alta queda de pressão)

Faixa de temperatura	-70°C ~ +300°C	-45°C ~ +250°C	-70°C ~ +200°C
Capacidade de arrefecimento	up to 7.5kW	up to 5.5kW	até 50kW

Cooling and Heating Systems (TES series)

Temperature Control Range: -85°C ~ +250°C

Temp Control Accuracy: ± 0.3°C

Faixa de temperatura	Série -45°C ~ +250°C	Série -85°C ~ +200°C	Série -60°C ~ +200°C
Capacidade de arrefecimento	até 25kW	até 25kW	até 60kW

Cooling and Heating Machines (LTS series)

Temperature Control Range: -80°C to +80°C

It is widely used in the semiconductor process to control the temperature of the reaction chamber, the hot sink plate and the non-flammable heat transfer medium.

Faixa de temperatura	Série -20°C ~ +80°C	Série -45°C ~ +80°C	Série -60°C ~ +80°C	Série -80°C ~ +80°C
Controlo do fluxo	7 ~ 45 L/min	7 ~ 45 L/min	7 ~ 45 L/min	7 ~ 45 L/min

Circuladores de arrefecimento e aquecimento

Gama de controlo de temperatura: -45°C a +250°C

Application: Various Reactors (Microchannels, Glass, Jacketed Reactors, etc.), Distillation or Extraction System, Laboratory, University, Research Institute, Aerospace, Chemical, Pharmaceutical, Petrochemical, Biochemical, Medical, Hospital, R&D Workshop, Aerospace, Biological and Other Industries.

Faixa de temperatura	Série -25°C ~ +200°C	Série -45°C ~ +250°C
Capacidade de arrefecimento	até 15kW	até 15kW

Circuladores de aquecimento

Gama de controlo de temperatura: +50°C a +300°C

Nota: A série UC pode controlar a temperatura do meio de transferência de calor. A série UST pode não só controlar a temperatura do meio de transferência de calor, mas também controlar a temperatura do material de reação.

Faixa de temperatura	+50°C ~ +200°C (UC series)	+50°C ~ +300°C (série UC)	+50°C ~ +300°C (série UST)
Capacidade de aquecimento	até 38kW	até 200kW	até 95kW

TCU Sistema de controlo da temperatura de multi-reactores

Gama de controlo de temperatura: -120°C a +250°C

Application: Various Reactors (Microchannels, Glass, Jacketed Reactors, etc.), Distillation or Extraction System, Laboratory, University, Research Institute, Aerospace, Chemical, Pharmaceutical, Petrochemical, Biochemical, Medical, Hospital, R&D Workshop, Aerospace, Biological and Other Industries.

Faixa de temperatura	Série -45°C ~ +250°C	Série -120°C ~ +250°C	Sistema de controlo de temperatura personalizado	RT+10°C ~ +135°C
Capacidade de aquecimento	até 80kW	até 80kW	Personalizado	up to 300kW